remote control NISSAN QUEST 2006 V42 / 3.G Quick Reference Guide

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02